20 Trailblazers Lead The Way In Patio Door Lock Repair

Patio Door Lock Repairs

Over time, patio doors undergo wear and tear which can lead to lock malfunctions. There are a few easy steps you can take to ensure the security of your uPVC door.

Whether it's realigning the lock or cleaning the mechanism that locks These simple fixes can help you make your home more secure.

Clean the Lock

Patio doors are great to let the outdoors in while keeping out the elements. However they can pose an issue for security when the lock isn't functioning properly. As time passes wear and tear, cold and hot weather dirt and debris can cause damage to your repairing patio doors door's lock and make it difficult to open. With a little attention you can ensure that your lock for your patio door always functions properly.

It's important to first clean the patio door lock and all moving parts. This helps remove any dirt and coatings that may be preventing the lock from functioning in the way it should. Begin by wiping down all the moving parts of the lock for your patio door with an aqueous cloth. Then, use a scouring cloth or a rough damp cloth to scrub the dirt-infested parts of the door frame and frame. Then, wipe the lock down with a dry cloth to get rid of any moisture. Let it air dry before using it.

If you have an exterior door that is fitted with a pin tumbler latch mechanism, you can grease the lock by applying powdered graphite to the key or by using an lubricant based on Teflon like WD-40 Multi-Use. This type of lubricant can be easy to apply, and it won't disintegrate as time passes. If you are unable to find the correct lubricant for your lock, you can make use of a pencil with a larger tip. Place the pencil into the lock, and shake it around to spread the graphite.

Sliding patio door tracks also require regular maintenance to keep them free of dust, dirt and other debris. These tracks are especially susceptible to snow and ice, which can cause them jam or bind, making it harder for your patio doors to open and close.

Tracks for sliding patio door lock repair patio doors and rollers can be cleaned by removing dirty or damaged weather stripping and cleaning them before reinstalling it. The rollers for patio doors can be cleaned and sprayed with a nonstick lubricant.

Lubricate the moving parts

uPVC French Doors, similar to sliding patios, operate using 3 to 4, or occasionally 5 point locking mechanisms. This includes the handle and lock cylinder that is operated with a key. These doors require maintenance, oiling of the moving parts. This can be accomplished with a thin oil however, never WD40. It should be done at least once a year.

If hinges that are sagging aren't the cause, the door could be misaligned and catching or hitting the strike plate hole within the frame. The solution is to take off the strike plate and use a sharp chisel to enlarge the mortise that it rests in. This will permit the latch to fit properly into the hole, and also prevent it from rubbing against the frame.

Once the cylinder is cleared of the way, measure its width with a book or piece of wood that can fit into the gap between the adjustment screw and the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder. the inner dimension runs from the center of the adjustment screw until the end of the cylinder.

Verify the lock's width

If your patio door latch is difficult to turn even after cleaning and lubricating, there's a possibility that it's out of alignment with the strike plate hole. Examine if the door is properly balanced and if the hinge screws are tight, but in many cases, moving the strike plate upwards or downwards could fix the problem.

The latch might not work properly when the strike of the lock is too small. In this case, you'll need to enlarge the hole using the hammer or chisel and then test the latch to ensure that it is able to engage the strike plate smoothly without rubbing against or landing on the frame of the door jamb.

You must identify the kind of mortise lock that you have before buying an alternative. This can be done by looking at the end faceplate and determining if it is round or square. Then, take a look at the screw holes in the existing lock and note the size of each one. This information will allow you to locate a replacement lock that is exactly the same size and will fit in the hole you have already.

You'll need to locate the mortise lock, and then examine it for bends, scratches or other damage that needs to be repaired. A badly bent or damaged latch is more likely than one that's been used a lot to break. Replace the lock if it displays indications of damage.

Once you've decided on the kind of lock replacement that you require It's time to start the actual repair. The old handle and spindle should be removed from the doorway to the patio doors repair near me. Install the new handle. Begin by installing the handle inside, aligning it with the spindle and then securing it with the two screws or bolts which hold it. Install the exterior handle following the interior handle. After you've completed these steps check the handles to make sure they can be shut and open easily and that the latch works correctly with the strikeplate.

Check the door's Strike

The door latch and strike plate are the two components of the lock that work to ensure that the latch locks the door. If these are misaligned and the latch isn't latching the door properly. Fortunately, this issue is usually easy to correct.

Examine the holes that receive the strike plate to ensure they are free of obstructions, such as dirt or plastic plugs. Then, loosen the keeper screws that hold the strike plate in place, allowing it to move vertically, but not separating it from the frame of the door. Then, adjust the strike plate so that its holes for receiving are aligned with the latch hooks on the door latch. After the strike plate has been adjusted, tighten the screws and then test the door to see if it shuts smoothly with the new adjustment.

Door strike plates can be a bit difficult to access for homeowners with sliding patio doors, however they're essential for locking and unlocking your door. These metal plates are usually located on the top and bottom of the door jamb which is where they are used to support the door's latch. The door latch slides into the strike plate and forms a seal. If the strike plate is damaged, rusted, or is not properly installed the latch might not properly lock the door.

The most common reason for an outdoor door lock to become stuck or not close is a misalignment between the latch and the strike plate. The easiest way to check for this is by performing the "lipstick test." Rub some lipstick on the edge of the deadbolt and attach masking tape over it. The lipstick will leave the mark when you shut the door. This will reveal exactly where the latch meets the strike plate. If the mark is too high or low you can easily adjust the strike plate.

If your sliding patio door locks aren't working correctly, they can keep your home secure from intruders. You must resolve this issue as quickly as possible. Follow these steps to repair your patio door lock and restore its function.